The CLIENT accepts the responsibility of ensuring that the pre-inspection requirements are met (appropriate shore power, potable water access, acceptable fuel and propane levels, etc.). Due to the RV absorption refrigerators’ cooling time, the refrigerator must have been in operation for at least 12 hours before an accurate temperature reading can be taken in the freezer and refrigerator compartments.
This report will consist of 40 to 80 photos that describe the items identified during the detailed Premier Motor Home Inspection.
Fluid analysis can be purchased in advance and will be performed during the inspection at an additional cost.
Roof
- Inspect and rate the overall roof condition
- Evaluate the condition of the various sealants and joints around the roofing components.
- Rate the condition of the roof vents, air conditioners, antenna, solar, satellite, Wi-Fi, and other components that are mounted on the roof.
Sidewall and End Caps
- Inspect and evaluate the appearance and functional condition of the end caps, sidewalls, entrance doors, windows, and cargo access doors.
- Inspect and evaluate any damage, discoloration, and delamination of the sidewall and end cap components.
Slideout Rooms
- Inspect and rate the roof condition
- Inspect and evaluate the condition of the seals, sweeps, and gaskets for possible damage.
- Evaluate the attached wiring and utility harness that feeds underneath the slideout room.
Awnings and Slideout Toppers
- Operate and rate the condition of the awning frames and latching mechanisms
- Evaluate and rate the condition of the fabric material of the awnings
Chassis Turn Signal and Running Lights (12 volt DC)
- Activate and evaluate the operation of the DOT lights
- Visually inspect the chassis battery compartment, the electrical connections, and the batteries
120 Volt AC Electrical System (house-type power)
- Inspect and rate the condition of the power cord and its connection ends
- Remove the cover panel of the 120-volt circuit breaker box to visually inspect the condition of the wiring, circuit breakers, and grounding connections
- Test and verify the converter’s output operation from 120 VAC to 12 VDC for charging the coach batteries.
Generator- Engine – if installed *strongly recommend performing oil analysis to determine internal combustion engine component condition.
- Identify and note the model, serial number, and run hours of the generator
- Check oil level
- Start, operate, and test the onboard generator
Generator – Radiator – if installed on this model of Generator, strongly recommend performing a coolant analysis to determine the condition of the coolant and the internal cooling system.
- Visually inspect the coolant reservoir, radiator, and hoses.
Inverter – if installed
- Identify and note the model and serial number of the inverter
- Visually inspect the wiring and electrical connections, and fuses/circuit breakers
Coach Battery System – (12 volt DC Battery Electrical System)
- Locate and note the location of the battery stack
- Evaluate the condition, age, and matched sizing of the battery stack.
- Access and visually inspect the wiring, fuse panel, and fuses of the 12-volt DC electrical system
- Evaluate the operation of the freshwater/wastewater monitor panel for incorrect tank readings
Fresh Water System
- Verify that the fresh water connections for the city water hookup are operational
- Verify the onboard fresh water tank and pressure pump system will operate and maintain pressure
- Operationally test all freshwater fixtures inside and outside of the RV
Waste Water Systems – (Gray and Black Water)
- Operationally test and inspect both waste (gray and black) plumbing systems for leaks under the sinks, shower, around the toilet, and discharge lines
- Operate both drain valves and test for ease of operation
- Verify the drain cap is in place and will hold wastewater
Life Safety Items
- Perform and document LP gas timed leak test at cooktop burner spud for 5 minutes at 8 inches of water column gas pressure
- Test the Ground Fault Circuit Interrupter (GFCI) circuits in the 6-foot range of the water areas of the bathroom, kitchen, and exterior receptacles
- Test all wall receptacles for correct polarity and ground fault
- Test the exterior skin for hot skin that would cause an electrical shock
- Emergency Exit Windows – Verify all safety windows are operational
- Fire Extinguisher – Verify the unit is secure in the bracket and that the dial indicates the extinguisher is fully charged
- Smoke/Fire Detector -Test and verify the operation of the unit and document the expiration date of the detector
- Carbon Monoxide Detector (if applicable) – Test and verify the operation of the unit and document the expiration date of the detector
- LP Gas Detector – Verify gas detection, audio alarm, and document the expiration date of the detector
- Verify the rubber grommet is properly sealed around the LP gas line of the water heater – if equipped
LP Gas System
- Visually inspect all hoses and pressure regulators for damage and age deterioration
- Verify the plastic cover has been installed over the regulator
ASME tank – if equipped
- Conduct a visual inspection of the tank for rust or physical damage if the tank is accessible
- Document the manufacture date of the ASME tank if accessible
- List the gallon capacity of the tank
Refrigerator
- Identify the brand, model, and type of refrigerator
- Operate on all heat sources: 120-volt AC, LP gas, and for 3-way refrigerators, 12-volt DC
- Collect serial and model numbers and verify with the manufacturer if a recall notice has been issued and completed for this unit
- Test for the interior temperature of upper and lower refrigerator compartments and ice maker (if installed) *if the refrigerator has been operating for a minimum of 12 hours
Water Heater – if equipped
- Identify the brand, model, and type of water heater
- Visually inspect the burner assembly and the gas exhaust system for blockages and insect infestation
- Fill the tank with water (if necessary) and verify operation on all heat sources – LP gas and 120-volt AC if equipped with a heating element.
Furnace – if equipped
- If accessible, identify the brand, model, and type of furnace(s) that have been installed
- Visually inspect air intake and exhaust assemblies for blockages and insect infestation
- Operate and verify warm air discharge out of vents and proper return airflow to the unit
Cooktop/ Stove
- Evaluate and rate the condition of the cooktop or stove
- Verify the ignition and operation of all top burners and the oven flame (if equipped)
- Inspect and rate the condition of the metal grill top and rubber grommets of the top burner area
Air Conditioner(s)
- Identify and list the type of cooling unit/heat pump
- Perform a cooling efficiency test (Delta T) on each unit
Washer/ Dryer – if installed
- Visually inspect and verify a wash and rinse cycle of the washer and dryer
- Evaluate and rate the exterior condition of the dryer exhaust vent
Microwave/Convection Oven
- Identify and list the brand, model, and type of the unit
- Operate the unit for 60 seconds, utilizing a cup of wate,r and then list the water temperature
Dishwasher – if installed
- Identify and list the brand and model of the unit
- Verify operation of the unit and inspect for leaks and non-functioning rotating racks and wash bars
In-House Vacuum System – if installed
- Identify and list the brand and model of the unit
- Verify the operation and visually inspect the various components of the hose assembly, access doors, and dirtbag
Electric Fireplace – if installed
- Identify and list the brand and model of the unit
- Operate and verify the various heat settings, fan speed levels, and the backlighting
Cooktop Exhaust Fan
- Operate and verify the condition of the exhaust function and fan speeds
- Evaluate and rate the exterior condition of the exhaust vent
Ceiling-Mounted Fans and Ceiling Exhaust Vents
- Visually inspect the condition of the blades and motor
- Operate and verify the condition of the blade direction and fan speeds
Interior Conditions and Appearance
- Visually inspect all ceilings, fans, walls, interior doors, and flooring for signs of water intrusion, surface damage, and/or staining or odors.
- Operate all windows, blinds, shades, and doors, noting any deficiencies or missing components.
- Operate all interior, exterior, and decor lighting – 12-volt and 120-volt
Cabinets and Closet Condition
- Inspect and evaluate all safes, cabinet doors, drawers, and pull-out operations.
- Visually inspect all countertops and flat surface areas of the kitchen, living room, bathroom, bedroom, and storage areas for scratches and damage
Furniture
- Visually inspect the condition of the dinette table/booth, chairs, recliners, and sofa
- Inspect and note furniture fabric tears, discoloration, and signs of excessive wear
- Visually inspect and note signs of mattress damage or staining
Entertainment System
- Visually inspect and operate all TV and stereo equipment
- Verify DVD/disc players and radios are operational
- Raise and lower the roof-mounted antenna if equipped
Shower/Tub Enclosure
- Visually inspect the glass panels, curtains, and soap dish areas
- Evaluate and rate the seals around the framework and doors for water leaks
- Operate the door and latch system to verify its operation
Motor Home – Please note the following items: Due to insurance restrictions, the Motor Home can NOT be driven by the Inspector. Also, due to the lack of clearance under the motor home and safety issues, the Inspector will conduct the following visual inspections from the outer perimeter of the motor home.
Chassis and Undercarriage
- Visually inspect for rust, damage, and excessive oil on the underside of the motor home
Steering
- Visually inspect for bent or damaged components and hydraulic leaks
Leveling System
- Verify the system operates properly by extending and retracting the leveling system
- Note visual indications of hydraulic leaks or mechanical issues
Engine *strongly recommends performing an oil analysis to determine the condition of the internal combustion engine component.
- Make and model of the engine
- Verify the oil level on the dipstick
- Indications of engine issues or any noises while running
- Note the oil pressure reading on the dashboard gauges
Radiator *strongly recommends performing coolant analysis to determine the condition of the coolant fluid and the internal cooling system.
- Location of the radiator and cooling fans
- Visually inspect the coolant reservoir, radiator, and hoses
Transmission *strongly recommends performing transmission fluid analysis to determine the fluid’s condition and the transmission’s internal components.
- Fluid level on dipstick
- Indications of contaminated transmission fluid
Running Gear (Motor Home)
- Type and number of axles
- Inspect the frame, axles, springs, rims, and other components for rust, oil stains, and visible damage
- Document the information on the tires as to their age, tire tread condition, and weight capacities
- Check tire pressure
Hitch System/Hook Up
- Inspect and identify the type of system used to tow vehicles
Weight Labels and Data Plates
- Identify and document the Vehicle Identification Number (VIN)
- Locate and document Vehicle Frame Number
- Document the license plate info
- List the inspection sticker information – if applicable
- List the RVIA inspection seal number
- List the Gross Vehicle Weight Rating
- List the date of manufacture